NUTMEG RGB-COMPOSITE VIDEO CONTROL CARDS
 
|
Many people have asked for ways to incorporate higher-quality electronic images (such as those from computers and line-doubled composite and component video) into their programs. These cards are the answer! Now you can have not only normal composite video in your programs, but high-definition images from computers (like the IBM PC and Apple Macintosh), and true component video sources, such as BetacamSP. (Note: these signals require projectors capable of displaying high frequency RGB signals and component video signals, respectively. Contact Sky-Skan for details.)
|
SPECIFICATIONS - RGB Composite Video Input Card- SS 276-141
INPUT/OUTPUT CONNECTIONS
RGB IN (1-5) - 15 pin high density female Dshell. DC coupled with 75 ohm termination impedance.
Pinout as follows:
01) Red Video
02) Green Video
03) Blue Video
04)
05) Signal Ground
06) Signal Ground
07) Signal Ground
08) Signal Ground
09)
10) Signal Ground
11)
12)
13)Composite (H/V) Sync
14)
15)
COMP IN 1-7 - 15 pin high density female Dshell. DC coupled with 75 ohm termination impedance.
Pinout as follows:
01) Composite 1 in
02) Composite 2 in
03) Composite 3 in
04)
05) Signal Ground
06) Signal Ground
07) Signal Ground
08) Signal Ground
09)
10) Signal Ground
11)
12) Composite 6 in
13) Composite 4 in
14) Composite 5 in
15) Composite 7 in
COMP MONITOR OUT - Single composite video output via gold phono connector. Outputs one of the composite inputs, selected by the front pushbutton. Capable of driving a 75 ohm cable over 100 ft.
PANEL CONTROLS
SELECT - Selects composite input connected to MONITOR OUTPUT.
PANEL DISPLAYS
COMPOSITE MONITOR - A Seven segment display showing sourceselected.
GENERAL CAPABILITIES
Buffers seven composite video sources, five RGBS signals and routes them to the NUTMEG internal video bus from which the output cards select sources. A seven channel multiplexer selects one of the composite sources for viewing via MONITOR OUTPUT.
DEVICES CURRENTLY SUPPORTED
PAL, NTSC, SECAM dependent upon the projector. RGB signals with combined sync or sync on green and bandwidth to 50 mHz.
MAXIMUM CABLE RUN
Unlike digital communications, video signals do not suddenly "fail" after a certain distance. Instead, as distance increases, the picture degrades in sharpness and color fidelity. For distances over 100 ft, we recommend that tests be made to determine if the picture quality is acceptable; use buffer amps if it is not. Always use low loss, high quality 75 ohm coaxial cable with reliable connectors for all video connections.
POWER REQUIREMENTS
Card draws necessary power directly from the NUTMEG
Card requires one open option-card slot in a NUTMEG
SS 276-141 NUTMEG RGB-Composite Video Input Card
SPECIFICATIONS - RGB Composite Projector Control Card - SS 276-142
INPUT/OUTPUT CONNECTIONS
RGB OUT TO PROJ. - 15 pin high density female Dshell. DC coupled with ability to drive a 75 ohm cable 100 ft.
Pinout as follows:
01) Red Video
02) Green Video
03) Blue Video
04)
05) Signal Ground
06) Signal Ground
07) Signal Ground
08) Signal Ground
09)
10) Signal Ground
11)
12)
13) Composite (H/V) Sync
14)
15)
LINE DOUBLER OUT - 15 pin high density female Dshell. DC coupled with ability to drive a 75 ohm cable 100 ft. Pinout as above.
LINE DOUBLER IN - 15 pin high density female Dshell. DC coupled with 75 ohm termination resistors. Pinout as above.
COMP VIDEO OUT - Single composite video output via BNC. Will drive 75 ohm cable 100 ft.
PROJECTOR CONTROL - 25 pin Dshell connector, modified RS232 pinout.
GENERAL CAPABILITIES
Does everything the SS 276-140 control card does. In addition there is a 12 bit fader in the RGB OUT TO PROJ. output. LINE DOUBLER input and output allow the bypass of a line doubler so computer graphics can be shown directly on the screen.
DEVICES CURRENTLY SUPPORTED
SONY VPH-1271, 1272, 1251, 1252 and comparable units.
BARCO BARCODATA & BARCOVISION 1100, 1101, 700, 701, and comparable units.
MAXIMUM CABLE RUN
100 ft nominal, see above for more details.
POWER REQUIREMENTS
Card draws necessary power directly from the NUTMEG
Card requires one open option-card slot in a NUTMEG
SS 276-142 NUTMEG RGB-Composite Projector Control Card with RGB Fader & Line Doubler Bypass
SPECIFICATIONS - RGB Monitor Card- SS 276-143
INPUT/OUTPUT CONNECTIONS
INPUT- All input is received from the BUS of the NUTMEG Chassis
RGBS OUT - 15 pin high density female Dshell. DC coupled with ability to drive a 75 ohm cable 100 ft.
Pinout as follows:
01) Red Video
02) Green Video
03) Blue Video
04)
05) Signal Ground
06) Signal Ground
07) Signal Ground
08) Signal Ground
09)
10) Signal Ground
11)
12)
13) Composite (H/V) Sync
14)
15)
RED OUT- Single composite video output via BNC. Will drive 75 ohm cable 100 ft.
GREEN OUT- Single composite video output via BNC. Will drive 75 ohm cable 100 ft.
BLUE OUT- Single composite video output via BNC. Will drive 75 ohm cable 100 ft.
COMP SYNC OUT- Single composite video output via BNC. Will drive 75 ohm cable 100 ft.
REMOTE - 2.5mm stereo phone jack
GENERAL CAPABILITIES
Compliments the NUTMEG SS 276 141 RGB Composite Video Control Card. Allows for an RGB sync signal to be run to local or remote monitors.
MAXIMUM CABLE RUN
100 ft nominal, see above for more details.
POWER REQUIREMENTS
Card draws necessary power directly from the NUTMEG
Card requires one open option-card slot in a NUTMEG
SS 276-143 NUTMEG RGB Monitor Card